Bob's Knobs for Celestron C9.25 f/10 Secondary with Metric Collimation Screw Threads
Stock count is accurate & shown in real time.
- This item is out of stock.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
- This item is out of stock.
- We have no ETA from the manufacturer at this time.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
Lower 48 States:
Orders over $50 ship free within the Lower 48 using a carrier and service we select based on your items and delivery location. Faster shipping options may be available at checkout.
U.S. Outside the Lower 48 (AK, HI, PR):
Free shipping on orders over $50 applies to many—but not all—items. Add items to your cart and enter your ZIP code to see available shipping options and any costs.
International Orders:
Free shipping does not apply to international orders. You’ll see available shipping options and costs during checkout. Some items can’t be shipped internationally due to size or manufacturer restrictions. Duties, taxes, brokerage fees, and tariffs are not included and are the customer’s responsibility.
Special Note: The Celestron 9.25" SCT uses either standard 6-32 or metric M3 collimation screws. Allen and set-style factory collimation screws have standard threads. For Phillips collimation screws, most silver screws are standard and most black screws are metric. See our hints for more information.
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C9.25metBO
Fits: Celestron 9.25" (23.5 cm) f/10 SCT versions with metric screw threads (CPC 925). Not for C9.25 with "Trifid" Faster or EdgeHD optics (see Item C9.25fst instead).
Knobs: Black oxide steel, 12 mm (1/2") diameter
Threads: Black oxide steel
Notes:
- Black Phillips factory collimation screws usually have metric threads, but some black Phillips screws have standard threads. Our hints will help you determine which screws are on your telescope. Make sure the knob threads match the factory screw threads before installing the knobs.
- Black oxide steel is for dry environments. Lightly oil the knob top and knob serrations periodically as an anti-corrosion measure.
- These knobs sit inside the tall lip around the perimeter of the secondary, so they may be hard to grasp with two fingers. Adjustments can be made using a thumb or finger against the inside edge of the knob.
- The factory dust cover will fit normally with Bob's Knobs installed.
- If your telescope has a factory-installed plastic cap over the collimation screws, it must be removed and set aside when Bob's Knobs are installed. The cover is cosmetic only and will not affect operation of the scope.
Other Information
- Country of Manufacture: United States
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C9.25metBO
Fits: Celestron 9.25" (23.5 cm) f/10 SCT versions with metric screw threads (CPC 925). Not for C9.25 with "Trifid" Faster or EdgeHD optics (see Item C9.25fst instead).
Knobs: Black oxide steel, 12 mm (1/2") diameter
Threads: Black oxide steel
Notes:
- Black Phillips factory collimation screws usually have metric threads, but some black Phillips screws have standard threads. Our hints will help you determine which screws are on your telescope. Make sure the knob threads match the factory screw threads before installing the knobs.
- Black oxide steel is for dry environments. Lightly oil the knob top and knob serrations periodically as an anti-corrosion measure.
- These knobs sit inside the tall lip around the perimeter of the secondary, so they may be hard to grasp with two fingers. Adjustments can be made using a thumb or finger against the inside edge of the knob.
- The factory dust cover will fit normally with Bob's Knobs installed.
- If your telescope has a factory-installed plastic cap over the collimation screws, it must be removed and set aside when Bob's Knobs are installed. The cover is cosmetic only and will not affect operation of the scope.
Special Note: The Celestron 9.25" SCT uses either standard 6-32 or metric M3 collimation screws. Allen and set-style factory collimation screws have standard threads. For Phillips collimation screws, most silver screws are standard and most black screws are metric. See our hints for more information.
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C9.25metBO
Fits: Celestron 9.25" (23.5 cm) f/10 SCT versions with metric screw threads (CPC 925). Not for C9.25 with "Trifid" Faster or EdgeHD optics (see Item C9.25fst instead).
Knobs: Black oxide steel, 12 mm (1/2") diameter
Threads: Black oxide steel
Notes:
- Black Phillips factory collimation screws usually have metric threads, but some black Phillips screws have standard threads. Our hints will help you determine which screws are on your telescope. Make sure the knob threads match the factory screw threads before installing the knobs.
- Black oxide steel is for dry environments. Lightly oil the knob top and knob serrations periodically as an anti-corrosion measure.
- These knobs sit inside the tall lip around the perimeter of the secondary, so they may be hard to grasp with two fingers. Adjustments can be made using a thumb or finger against the inside edge of the knob.
- The factory dust cover will fit normally with Bob's Knobs installed.
- If your telescope has a factory-installed plastic cap over the collimation screws, it must be removed and set aside when Bob's Knobs are installed. The cover is cosmetic only and will not affect operation of the scope.
Other Information
- Country of Manufacture: United States
| Free Shipping Graphic | Free US Shipping |
|---|---|
| Hide Found a better Shipped Price on Frontend? | No |
Bob's Knobs for Celestron C9.25 f/10 Secondary with Metric Collimation Screw Threads