Bob's Knobs for Celestron C8 f/10 Post-1980 Secondary with Standard Collimation Screw Threads
Stock count is accurate & shown in real time.
- This item is out of stock.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
- This item is out of stock.
- We have no ETA from the manufacturer at this time.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
Lower 48 States:
Orders over $50 ship free within the Lower 48 using a carrier and service we select based on your items and delivery location. Faster shipping options may be available at checkout.
U.S. Outside the Lower 48 (AK, HI, PR):
Free shipping on orders over $50 applies to many—but not all—items. Add items to your cart and enter your ZIP code to see available shipping options and any costs.
International Orders:
Free shipping does not apply to international orders. You’ll see available shipping options and costs during checkout. Some items can’t be shipped internationally due to size or manufacturer restrictions. Duties, taxes, brokerage fees, and tariffs are not included and are the customer’s responsibility.
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C8std
Fits: Celestron 8” (20 cm) f/10 post-1980 SCT with factory Allen or silver Phillips collimation screws, with or without Fastar secondary with silver collimation screws (C8 black, or gray; Ultima 2000; NexStar 8; many others). This includes the post-2005 orange-tube. Will NOT fit pre-1980 orange tube or most scopes with black Phillips factory collimation screws.
Knobs: Black plastic, 13 mm (1/2") diameter
Threads: Black anodized aluminum alloy
Notes:
- These knobs will fit C8 models made prior to 2005 (except pre-1980 orange tube, and most post-2005 models with silver factory collimation screws.
- Most models with black Phillips factory collimation screws (see fourth photo) require C8 metric knobs (Item C below). However, a few post-2005 scopes have black Phillips collimation screws with standard threads. Here are some hints to help determine which screws your telescope has. Make sure the knob threads match the factory screw threads before installing the knobs.
- We provide spacers to raise the knobs slightly for easier use, but the spacers can be omitted if the knobs contact the inside of the full-aperture dust cover. Spacers are required for knobs installed on the Fastar secondary with silver collimation screws (see fifth photo) for proper clearance.
- Some telescope versions have a small plastic cover over the factory collimation screws. This cover must be removed and set aside when Bob's Knobs are installed. The cover is cosmetic only and will not affect operation of the scope.
Other Information
- Country of Manufacture: United States
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C8std
Fits: Celestron 8” (20 cm) f/10 post-1980 SCT with factory Allen or silver Phillips collimation screws, with or without Fastar secondary with silver collimation screws (C8 black, or gray; Ultima 2000; NexStar 8; many others). This includes the post-2005 orange-tube. Will NOT fit pre-1980 orange tube or most scopes with black Phillips factory collimation screws.
Knobs: Black plastic, 13 mm (1/2") diameter
Threads: Black anodized aluminum alloy
Notes:
- These knobs will fit C8 models made prior to 2005 (except pre-1980 orange tube, and most post-2005 models with silver factory collimation screws.
- Most models with black Phillips factory collimation screws (see fourth photo) require C8 metric knobs (Item C below). However, a few post-2005 scopes have black Phillips collimation screws with standard threads. Here are some hints to help determine which screws your telescope has. Make sure the knob threads match the factory screw threads before installing the knobs.
- We provide spacers to raise the knobs slightly for easier use, but the spacers can be omitted if the knobs contact the inside of the full-aperture dust cover. Spacers are required for knobs installed on the Fastar secondary with silver collimation screws (see fifth photo) for proper clearance.
- Some telescope versions have a small plastic cover over the factory collimation screws. This cover must be removed and set aside when Bob's Knobs are installed. The cover is cosmetic only and will not affect operation of the scope.
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C8std
Fits: Celestron 8” (20 cm) f/10 post-1980 SCT with factory Allen or silver Phillips collimation screws, with or without Fastar secondary with silver collimation screws (C8 black, or gray; Ultima 2000; NexStar 8; many others). This includes the post-2005 orange-tube. Will NOT fit pre-1980 orange tube or most scopes with black Phillips factory collimation screws.
Knobs: Black plastic, 13 mm (1/2") diameter
Threads: Black anodized aluminum alloy
Notes:
- These knobs will fit C8 models made prior to 2005 (except pre-1980 orange tube, and most post-2005 models with silver factory collimation screws.
- Most models with black Phillips factory collimation screws (see fourth photo) require C8 metric knobs (Item C below). However, a few post-2005 scopes have black Phillips collimation screws with standard threads. Here are some hints to help determine which screws your telescope has. Make sure the knob threads match the factory screw threads before installing the knobs.
- We provide spacers to raise the knobs slightly for easier use, but the spacers can be omitted if the knobs contact the inside of the full-aperture dust cover. Spacers are required for knobs installed on the Fastar secondary with silver collimation screws (see fifth photo) for proper clearance.
- Some telescope versions have a small plastic cover over the factory collimation screws. This cover must be removed and set aside when Bob's Knobs are installed. The cover is cosmetic only and will not affect operation of the scope.
Other Information
- Country of Manufacture: United States
| Free Shipping Graphic | Free US Shipping |
|---|---|
| Hide Found a better Shipped Price on Frontend? | No |
Bob's Knobs for Celestron C8 f/10 Post-1980 Secondary with Standard Collimation Screw Threads