Bob's Knobs for C11 f/10 with “Trifid” Fastar Secondary Housing and Metric Collimation Screw Threads

Stock count is accurate & shown in real time.
- This item is out of stock.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
- This item is out of stock.
- We have no ETA from the manufacturer at this time.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
Lower 48 States:
Orders over $50 ship free within the Lower 48 using a carrier and service we select based on your items and delivery location. Faster shipping options may be available at checkout.
U.S. Outside the Lower 48 (AK, HI, PR):
Free shipping on orders over $50 applies to many—but not all—items. Add items to your cart and enter your ZIP code to see available shipping options and any costs.
International Orders:
Free shipping does not apply to international orders. You’ll see available shipping options and costs during checkout. Some items can’t be shipped internationally due to size or manufacturer restrictions. Duties, taxes, brokerage fees, and tariffs are not included and are the customer’s responsibility.
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C11metfst
Fits: Celestron 11” (28 cm) f/10 SCT versions (metal or carbon fiber tube) with metric thread factory collimation screws and Fastar secondary housing. This housing can have either a "Trifid" rotary cover ( second photo above) or a simple knob in the center (fourth photo) and no rotary cover. Factory collimation screws are black Phillips. These knobs will fit the C11 with EdgeHD optics (third photo). They will also fit the C11 with Starizona Hyperstar (fifth photo) only if the collimation screws have metric threads.
Knobs: Black plastic, 16 mm (5/8”) diameter
Threads: Stainless steel
Notes:
- These telescopes can have factory collimation screws with either standard or metric threads. Most models with black Phillips collimation screws have metric threads. There are a few black Phillips screws with standard threads. See our hints for more information. If you discover your knobs have the wrong threads, you can return them for a refund and order the correct knobs. Alternatively, you can order knobs with both standard and metric thread screws and return the unused set for a full refund.
- Collimation screws on these telescopes are small with very fine threads. Knobs must be tightened gently (just enough to hold the secondary in place) to prevent damage to either the knob or secondary assembly.
- The factory dust cover will fit normally with Bob’s Knobs installed.
- If your telescope has a rotary secondary cover, it must remain open when the knobs are installed. The cover is cosmetic only and will not affect operation of the telescope.
Other Information
- Country of Manufacture: United States
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C11metfst
Fits: Celestron 11” (28 cm) f/10 SCT versions (metal or carbon fiber tube) with metric thread factory collimation screws and Fastar secondary housing. This housing can have either a "Trifid" rotary cover ( second photo above) or a simple knob in the center (fourth photo) and no rotary cover. Factory collimation screws are black Phillips. These knobs will fit the C11 with EdgeHD optics (third photo). They will also fit the C11 with Starizona Hyperstar (fifth photo) only if the collimation screws have metric threads.
Knobs: Black plastic, 16 mm (5/8”) diameter
Threads: Stainless steel
Notes:
- These telescopes can have factory collimation screws with either standard or metric threads. Most models with black Phillips collimation screws have metric threads. There are a few black Phillips screws with standard threads. See our hints for more information. If you discover your knobs have the wrong threads, you can return them for a refund and order the correct knobs. Alternatively, you can order knobs with both standard and metric thread screws and return the unused set for a full refund.
- Collimation screws on these telescopes are small with very fine threads. Knobs must be tightened gently (just enough to hold the secondary in place) to prevent damage to either the knob or secondary assembly.
- The factory dust cover will fit normally with Bob’s Knobs installed.
- If your telescope has a rotary secondary cover, it must remain open when the knobs are installed. The cover is cosmetic only and will not affect operation of the telescope.
Collimate your Catadioptric or Newtonian reflector style telescopes without tools!
It's easy...just grab a Bob's Knob collimation thumbscrew and turn. You can even do it while looking through the eyepiece on most scopes. These thumbscrews are also much easier to use with gloves on. And perhaps most importantly, you'll never drop that pesky little Allen wrench or screwdriver into the grass again. Installation is a snap with the included instructions, and you can undo the modification at any time.
Part: C11metfst
Fits: Celestron 11” (28 cm) f/10 SCT versions (metal or carbon fiber tube) with metric thread factory collimation screws and Fastar secondary housing. This housing can have either a "Trifid" rotary cover ( second photo above) or a simple knob in the center (fourth photo) and no rotary cover. Factory collimation screws are black Phillips. These knobs will fit the C11 with EdgeHD optics (third photo). They will also fit the C11 with Starizona Hyperstar (fifth photo) only if the collimation screws have metric threads.
Knobs: Black plastic, 16 mm (5/8”) diameter
Threads: Stainless steel
Notes:
- These telescopes can have factory collimation screws with either standard or metric threads. Most models with black Phillips collimation screws have metric threads. There are a few black Phillips screws with standard threads. See our hints for more information. If you discover your knobs have the wrong threads, you can return them for a refund and order the correct knobs. Alternatively, you can order knobs with both standard and metric thread screws and return the unused set for a full refund.
- Collimation screws on these telescopes are small with very fine threads. Knobs must be tightened gently (just enough to hold the secondary in place) to prevent damage to either the knob or secondary assembly.
- The factory dust cover will fit normally with Bob’s Knobs installed.
- If your telescope has a rotary secondary cover, it must remain open when the knobs are installed. The cover is cosmetic only and will not affect operation of the telescope.
Other Information
- Country of Manufacture: United States
| Free Shipping Graphic | Free US Shipping |
|---|---|
| Hide Found a better Shipped Price on Frontend? | No |

Bob's Knobs for C11 f/10 with “Trifid” Fastar Secondary Housing and Metric Collimation Screw Threads


















