Astrodymium Rotating Tilt Adjusters for Select Threads

Lower 48 States:
Orders over $50 ship free within the Lower 48 using a carrier and service we select based on your items and delivery location. Faster shipping options may be available at checkout.
U.S. Outside the Lower 48 (AK, HI, PR):
Free shipping on orders over $50 applies to many—but not all—items. Add items to your cart and enter your ZIP code to see available shipping options and any costs.
International Orders:
Free shipping does not apply to international orders. You’ll see available shipping options and costs during checkout. Some items can’t be shipped internationally due to size or manufacturer restrictions. Duties, taxes, brokerage fees, and tariffs are not included and are the customer’s responsibility.
Please note that this is a 3d printed plastic part.
These Astrodymium rotating tilt adjusters compensate for tilt in your imaging train when using any threaded adapter or extension tube. The adapter only needs to be partially unthreaded to allow the tilter to rotate to the area that needs to be compensated for.
The M42 size in particular is designed for use with ZWO's EOS/Nikon adapters, but it will also work with any M42 male thread.
Note:
- Each tilt adjuster adds 0.40mm ± 0.02mm of backfocus.
Each set comes with 3 levels of adjustment: 0.1, 0.2, and 0.3mm, and the corresponding amount is debossed onto the adjuster itself with roman numerals.
- I = 0.1mm
- II = 0.2mm
- III = 0.3mm
How does it work?
A raised section on each adjuster acts as a shim, which pushes one side of a threaded adapter higher than the other, this is the mechanism that creates the tilt effect.
The maximum amount of compensation that can be produced is dependent on the tolerance of the threads (how much slop they have).
For example, ZWO's extension tubes (16.5 & 21mm) have been tested to produce a maximum of 0.20mm worth of tilt.
This item is made out of UV resistant PETG plastic and can handle a temperature of up to 70°C (158°F) without deformation.
Other Information
- Country of Manufacture: Canada
Please note that this is a 3d printed plastic part.
These Astrodymium rotating tilt adjusters compensate for tilt in your imaging train when using any threaded adapter or extension tube. The adapter only needs to be partially unthreaded to allow the tilter to rotate to the area that needs to be compensated for.
The M42 size in particular is designed for use with ZWO's EOS/Nikon adapters, but it will also work with any M42 male thread.
Note:
- Each tilt adjuster adds 0.40mm ± 0.02mm of backfocus.
Each set comes with 3 levels of adjustment: 0.1, 0.2, and 0.3mm, and the corresponding amount is debossed onto the adjuster itself with roman numerals.
- I = 0.1mm
- II = 0.2mm
- III = 0.3mm
How does it work?
A raised section on each adjuster acts as a shim, which pushes one side of a threaded adapter higher than the other, this is the mechanism that creates the tilt effect.
The maximum amount of compensation that can be produced is dependent on the tolerance of the threads (how much slop they have).
For example, ZWO's extension tubes (16.5 & 21mm) have been tested to produce a maximum of 0.20mm worth of tilt.
This item is made out of UV resistant PETG plastic and can handle a temperature of up to 70°C (158°F) without deformation.
Please note that this is a 3d printed plastic part.
These Astrodymium rotating tilt adjusters compensate for tilt in your imaging train when using any threaded adapter or extension tube. The adapter only needs to be partially unthreaded to allow the tilter to rotate to the area that needs to be compensated for.
The M42 size in particular is designed for use with ZWO's EOS/Nikon adapters, but it will also work with any M42 male thread.
Note:
- Each tilt adjuster adds 0.40mm ± 0.02mm of backfocus.
Each set comes with 3 levels of adjustment: 0.1, 0.2, and 0.3mm, and the corresponding amount is debossed onto the adjuster itself with roman numerals.
- I = 0.1mm
- II = 0.2mm
- III = 0.3mm
How does it work?
A raised section on each adjuster acts as a shim, which pushes one side of a threaded adapter higher than the other, this is the mechanism that creates the tilt effect.
The maximum amount of compensation that can be produced is dependent on the tolerance of the threads (how much slop they have).
For example, ZWO's extension tubes (16.5 & 21mm) have been tested to produce a maximum of 0.20mm worth of tilt.
This item is made out of UV resistant PETG plastic and can handle a temperature of up to 70°C (158°F) without deformation.
Other Information
- Country of Manufacture: Canada
| Product Status | new |
|---|---|
| Free Shipping Graphic | Free US Shipping |
| Hide Found a better Shipped Price on Frontend? | No |

Astrodymium Rotating Tilt Adjusters for Select Threads


















