Agena 1.25" Cheshire Collimating Eyepiece for Refractors
Stock count is accurate & shown in real time.
- This item is out of stock.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
- This item is out of stock.
- We have no ETA from the manufacturer at this time.
- Sign up for back-in-stock alerts to be notified when this item becomes available.
Lower 48 States:
Orders over $50 ship free within the Lower 48 using a carrier and service we select based on your items and delivery location. Faster shipping options may be available at checkout.
U.S. Outside the Lower 48 (AK, HI, PR):
Free shipping on orders over $50 applies to many—but not all—items. Add items to your cart and enter your ZIP code to see available shipping options and any costs.
International Orders:
Free shipping does not apply to international orders. You’ll see available shipping options and costs during checkout. Some items can’t be shipped internationally due to size or manufacturer restrictions. Duties, taxes, brokerage fees, and tariffs are not included and are the customer’s responsibility.
Is collimating your refractor a real chore? Collimating your refractor is quick and easy when you use this 1.25" Cheshire collimating eyepiece.
To use this eyepiece, simply cap the telescope, remove the diagonal, and place the eyepiece directly in the focuser. Use natural daylight or shine a flashlight into the side opening with the 45-deg angled silver plate. Look into the small opening at the top of the eyepiece. You will see one or more small faint circles (usually overlapping) near the center. Each of these circles is a reflection from a lens surface of your telescope’s objective. Adjust the objective cell's push-pull bolts until the small circles merge into one. That’s it! With precise collimation, your refractor telescope will deliver the best image it can.
No additional instructions are included with this product, but you can easily find additional information about Cheshire eyepieces and their use on the internet. The dual images can sometimes be hard to see (especially in very bright or very faint light) but you will see them. As with most other telescope collimation/alignment procedures, use of this accessory requires patience and experience.
When collimating the refractor, it is necessary to remove the crosshairs at the bottom of the eyepiece. This is easily done with a flathead screwdriver or spanner wrench, but be careful not to damage the crosshairs!
With the crosshairs in the eyepiece, this Cheshire can also be used to collimate Newtonian reflectors. However, with most Newtonians, especially those with a focal ratio slower than f/4.5 approximately, you may get more accurate collimation with a longer Cheshire eyepiece which makes it easier to more precisely position the crosshairs in the center of the primary and secondary mirrors.
This Cheshire eyepiece fits in 1.25" focusers or in 2"-1.25" adapters. Weight = 2.8oz. Total length is approx. 65mm / 2.5". Insertion length is approx. 22mm / 0.86. Please see schematic diagram in photo 3 above for detailed measurements.
Please also note the following:
- Use of this item assumes that your focuser is aligned properly with your telescope tube.
- This item can only be used if your refractor telescope cell has a push-pull or other mechanism to adjust the lens elements. It will be of no use with fixed cell objectives that cannot be adjusted.
- You may notice a small dimple on the angled silver plate. This is a manufacturing artifact and not a defect. This will have no impact on its performance.
Other Information
- Country of Manufacture: China
Is collimating your refractor a real chore? Collimating your refractor is quick and easy when you use this 1.25" Cheshire collimating eyepiece.
To use this eyepiece, simply cap the telescope, remove the diagonal, and place the eyepiece directly in the focuser. Use natural daylight or shine a flashlight into the side opening with the 45-deg angled silver plate. Look into the small opening at the top of the eyepiece. You will see one or more small faint circles (usually overlapping) near the center. Each of these circles is a reflection from a lens surface of your telescope’s objective. Adjust the objective cell's push-pull bolts until the small circles merge into one. That’s it! With precise collimation, your refractor telescope will deliver the best image it can.
No additional instructions are included with this product, but you can easily find additional information about Cheshire eyepieces and their use on the internet. The dual images can sometimes be hard to see (especially in very bright or very faint light) but you will see them. As with most other telescope collimation/alignment procedures, use of this accessory requires patience and experience.
When collimating the refractor, it is necessary to remove the crosshairs at the bottom of the eyepiece. This is easily done with a flathead screwdriver or spanner wrench, but be careful not to damage the crosshairs!
With the crosshairs in the eyepiece, this Cheshire can also be used to collimate Newtonian reflectors. However, with most Newtonians, especially those with a focal ratio slower than f/4.5 approximately, you may get more accurate collimation with a longer Cheshire eyepiece which makes it easier to more precisely position the crosshairs in the center of the primary and secondary mirrors.
This Cheshire eyepiece fits in 1.25" focusers or in 2"-1.25" adapters. Weight = 2.8oz. Total length is approx. 65mm / 2.5". Insertion length is approx. 22mm / 0.86. Please see schematic diagram in photo 3 above for detailed measurements.
Please also note the following:
- Use of this item assumes that your focuser is aligned properly with your telescope tube.
- This item can only be used if your refractor telescope cell has a push-pull or other mechanism to adjust the lens elements. It will be of no use with fixed cell objectives that cannot be adjusted.
- You may notice a small dimple on the angled silver plate. This is a manufacturing artifact and not a defect. This will have no impact on its performance.
Is collimating your refractor a real chore? Collimating your refractor is quick and easy when you use this 1.25" Cheshire collimating eyepiece.
To use this eyepiece, simply cap the telescope, remove the diagonal, and place the eyepiece directly in the focuser. Use natural daylight or shine a flashlight into the side opening with the 45-deg angled silver plate. Look into the small opening at the top of the eyepiece. You will see one or more small faint circles (usually overlapping) near the center. Each of these circles is a reflection from a lens surface of your telescope’s objective. Adjust the objective cell's push-pull bolts until the small circles merge into one. That’s it! With precise collimation, your refractor telescope will deliver the best image it can.
No additional instructions are included with this product, but you can easily find additional information about Cheshire eyepieces and their use on the internet. The dual images can sometimes be hard to see (especially in very bright or very faint light) but you will see them. As with most other telescope collimation/alignment procedures, use of this accessory requires patience and experience.
When collimating the refractor, it is necessary to remove the crosshairs at the bottom of the eyepiece. This is easily done with a flathead screwdriver or spanner wrench, but be careful not to damage the crosshairs!
With the crosshairs in the eyepiece, this Cheshire can also be used to collimate Newtonian reflectors. However, with most Newtonians, especially those with a focal ratio slower than f/4.5 approximately, you may get more accurate collimation with a longer Cheshire eyepiece which makes it easier to more precisely position the crosshairs in the center of the primary and secondary mirrors.
This Cheshire eyepiece fits in 1.25" focusers or in 2"-1.25" adapters. Weight = 2.8oz. Total length is approx. 65mm / 2.5". Insertion length is approx. 22mm / 0.86. Please see schematic diagram in photo 3 above for detailed measurements.
Please also note the following:
- Use of this item assumes that your focuser is aligned properly with your telescope tube.
- This item can only be used if your refractor telescope cell has a push-pull or other mechanism to adjust the lens elements. It will be of no use with fixed cell objectives that cannot be adjusted.
- You may notice a small dimple on the angled silver plate. This is a manufacturing artifact and not a defect. This will have no impact on its performance.
Other Information
- Country of Manufacture: China
| Free Shipping Graphic | Free US Shipping |
|---|---|
| Special Text Below Specs | The following site presents excellent illustrated instructions explaining how this works. Scroll down about half-way to the "Cheshire Eyepiece Collimation" section. |
| Hide Found a better Shipped Price on Frontend? | No |
Agena 1.25" Cheshire Collimating Eyepiece for Refractors